When you would install a new item, you should not forget the steps as to how it will be placed. You should follow them so you can correctly install any Profile Design Cobra bars. This has been required on the policies of its warranty which will be given to the buyer. If you have no knowledge on this, you can ask for help from a dealer nearby.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
About the Author:
You can visit www.sportfactoryproshop.com for more helpful information about Procedures On Installing Profile Design Cobra Bars You Must Follow.
No comments :
Post a Comment